Hydrocal 1003 Offshore

Hydrocal 1003 Offshore 

Transformer Online Monitoring System with Gas-in-Oil and Moisture in Oil Measurement

The analysis of the gases dissolved in power transformer oil (DGA, DissolvedGas Analysis) is recognised as the most useful tool for detecting and diagnosing incipient faults in transformers.

In addition, water contamination deteriorates the performance of the oil as high moisture content increases the risk of corrosion and overheating, particularly when the water content reaches the oil's saturation point and free water is formed.

Besides regular gas chromatographic analysis and off-line moisture analysis of the isolation oil of power transformers, online monitoring systems are becoming more important worldwide.

By online monitoring of the key fault gases, Hydrogen (H₂) and Carbon Monoxide (CO) and Moisture in Oil (H₂O), an additional potential of cost reductions and safety improvements can be achieved.

Key Advantages

• Individual analysis of the dissolved gas contents hydrogen (H₂) and carbon monoxide (CO)
• Analysis of moisture (H₂O) dissolved in transformer oil (both relative humidity [%] and absolute humidity [ppm])
• Special design for Offshore Wind Power Applications:
• Housing without window painted C5M
• Backplate with 2 cable glands M20 (chrome-nickel steel, IP 55, corrosion-free and acid-resistant). Optional with 4 cable glands (2x M20 and 2 x M25).
• Backplate, oil entrance and housing screws made of stainless steel V4A
• Easy to mount on a transformer valve (G 1½" DIN ISO 228-1 or 1½" NPT ANSI B 1.20.1)
• Installation on the operational transformer without any operational interruption
• Advanced software (on the unit and via PC)
• Maintenance-free system
• Communication interfaces ETHERNET (Option) 10/100 Mbit/s (copper-wired / RJ45 or fibre-optical / SC duplex), RS 232 and RS 485 to support MODBUS^® RTU/ASCII, DNP3 and proprietary communication protocols and to be open/prepared for substation communication protocol IEC 61850
• Optional, internal 2G/3G modem with ext. adhesive antenna
• Optional DNP3 serial modem for SCADA connection
• Optional IEC 61850 modem for SCADA connection

Transformer Monitoring Functions

The Hydrocal 1003 Offshore can be used as a complete monitoring system for the condition of the transformer. The main monitoring options are listed below:

Voltages & Currents

• via voltage and current transformers/transducer

Temperature Monitoring

• Bottom and top oil temperature, ambient temperature (via additional temperature sensors)

Cooling Stage / Tap Changer Position

• (e.g. via current transducer)

Free configuration

• Analog inputs can be free allocated to any additional sensor

Further Calculations:

• Hot-Spot
• Loss-of-Life
• Ageing Rate

Communication

RS 232 (Standard)

• RS 232 interface (connection on backplate - without removing protection cover)
• On-site, e.g. with notebook via a proprietary protocol

RS 485 (Standard)

• Bus-Operation or point-to-point operation
• MODBUS^® RTU/ASCII or proprietary protocol
• Bus length up to 1000 m
• Communication with up to 31 HYDROCAL units
• Configuration via internal firmware or PC software HYDROSOFT

GSM modem (Option)

• Internal 2G/3G modem with external adhesive antenna and cable
• Proprietary protocol

Analog modem (Option)

• Integrated on-board analog modem with connection cable 15 m
• Proprietary protocol

Ethernet modem (Option)

• Internal ETHERNET 10/100 Mbit/s communication modem (copper-wired / RJ45 or fibre-optical / SC duplex)
• IEC 61850 (prepared) or proprietary protocol

DNP3 modem (Option)

• Internal DNP3 serial modem with RS 485 interface
• DNP3 protocol

Unit Mounting

Transformer without cooling system

Mounting of the HYDROCAL 1003 Offshore unit on a valve on the transformer tank.

Natural oil convection inside of the transformer is ensuring the exchange of the oil at the membrane.    

Transformer with cooling system and forced oil flow

The HYDROCAL 1003 Offshore unit is mounted on a T-fitting valve on the return flow of the cooling system.

The forced oil convection is ensuring the exchange of the oil at the membrane.

HydroSoft PC-Software

Program key features

• Configuration and administration of each individual HYDROCAL unit
• Data and configuration readout of HYDROCAL units
• Processing and presentation of data readout (Trend or table)
• Further processing of the processed data (Excel, CSV, clipboard and printing)
• Storage of the processed data and unit configuration
• Automatic data readout and alerting by e-mail

Key Features

• 230V AC or 110V DC supply
• Connection to valve: NPT 1” ½ or DIN-ISO 1” ½
• Degree of protection: IP55
• 4 digital relay outputs (220 VDC/VAC / 2 A / 60 W)
• 8 optocoupler (UCE: 24 V - ICE: 40 mA max.)
• 8 analog DC outputs
• 4 current DC 4-20 mA
• Communication: RS 232 serial interface and MODBUS® RTU
• Version suitable for corrosive environments, painted C5M, V4A stainless steel and IP 68 chrome-nickel cable glands, corrosion-free and acid-resistant

Operation principle

• Diffusion principle with gas-permeable TEFLON membrane
• Micro-electronic gas sensors for H₂ measurement
• Electro-chemical measurement cell for CO measurement
• Thin-film capacitive moisture sensor for H₂O measurement (relative [%] and absolute [ppm])
• Temperature sensors (oil temperature, gas temperature, backplate temperature)